AIM DIY: No Sew Woven T-Shirt Rag Rug

IMG_1337_tshirtrug
From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

A couple of months ago I tore up the carpet in my office and replaced it with a wood-ish surface. It’s been great through these warm months, but I want something to stand on when the cold sneaks in. Couple that need with a stack of t-shirts left over from the quilt project, and you have my newest best friend, the t-shirt rag rug.

IMG_1019_tshirtrug
I built a 30″x30″ make-shift loom out of a piece of plywood and scrap wood, but if you search online you can find frames built from pretty much anything. (A Beautiful Mess used cotton scraps and a big piece of cardboard. Also, Pinterest)

IMG_1016_tshirtrug
I put nails along each end, 1 inch apart. Good hammer practice for a hammer novice.

IMG_1063_tshirtrug
With the loom assembled, I moved to materials.

SUPPLIES

Stripping

The rug was built with 1.5″ loops for the warp (base strips) of my rug, and 1.75″ strips woven through.

IMG_1044_tshirtrug
I used a large straight rotary blade and a metal ruler to cut three navy shirts into the 1.5″ loops, then cut the rest of the shirts into 1.75″ strips. (This is a very forgiving fabric, so estimation is ok!)

IMG_1072_tshirtrug
I hooked the navy warp pieces on each side of the loom using the natural loop and stretch of the t-shirt.

IMG_1086_tshirtrug
I prepared to weave by attaching the first strip to the first warp loop. I cut a slit in one end of the strip, fed the other end around the first warp piece and back through the slit. Then I pulled it tightly and began to weave.

Not a normal knot.

I connected a lot of strips to finish this rug using the method shown below. It’s quick and tidy, and ensured you don’t have a lot of extra bulk at your connection points.

IMG_1222_tshirtrug

  1. Cut a small slit in the ends of each strip.
  2. Feed the new strip into the hole at the end of the other.
  3. Take the other end of the new strip and feed it through the slit on the same strip.
  4. Pull on the new end to tighten the knot. Smooth or trim extra material if needed.

(The video below shows how I knotted at the end of a strip.)

Now Weave!

IMG_1112_tshirtrug
Starting at that first warp piece, I wove in and out of each loop to the end of the loom. At the end I wrapped either over or under the last piece to start back down the loom. The second strand went over the strands that the first went under, and vice versa.

IMG_1122_tshirtrug
From there it was basically rinse and repeat. I wove back and forth, connecting strips and changing colors.

IMG_1139_tshirtrug
When possible I fed the strip through the warp flat, then pulled it down with my fingers to bunch it up.

IMG_1223_tshirtrug
The pattern and color combination were very important to me, and I got more and more excited as I worked on it. When I put the final strip in, I tied it off using a normal knot on the last piece of navy.

Finishing it off

Here’s where I admit this rug is really just a gigantic pot holder, and I finished it off the same way. I pulled the first warp loop free and fed the second through it, then fed the third through that one, and so on down the line. (Video Below)

IMG_1330_tshirtrug
Once I was down to the last two loops, I changed tactics. I cut the loop of the last piece, fed one strip through the second to last loop and tied it off.

IMG_1334_tshirtrug
I did the same thing on the other end and suddenly had a rug in front of me.

IMG_1350_tshirtrug

IMG_1344_tshirtrug
After basking in the last moments of sunshine, I rolled up the rug and brought it inside.

IMG_1360_tshirtrug
Where it was immediately claimed by another friend…

IMG_1368_tshirtrug
Cooper.

IMG_1380_tshirtrug
Looks like I’ll have to weave another rug for myself.

Next Time

  • The next rug will be bigger. Once I took this one off the loom it shrunk down a bit, and I love it too much for it to be small.
  • I won’t pull the woven strands as tightly, which will hopefully help with the shrinking.
  • Maybe I’ll try non-stretch cotton scraps?
  • I will plan to move the loom frame around a lot, and possibly rig up some way of leaning it upright while I’m weaving. Working flat gave me a back-ache.
  • I will take it in little batches, weaving in front of the tv or in public. If I weave in public I will look very serious about turning scraps into a comfy rug.

A sign of a successful project is the ability to look forward to the next one.

UPDATE: I enjoyed this project so much that I decided to remake this rug- BIGGER! I built a much larger loom using scrap wood and screws, then followed the same process to build this monstrosity. It sits cozily by my work table now, warms my feet, and makes me happy.

IMG_2188_roundtshirtrug