From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.
My friend Tara is a paper maché inspiration. A couple of years ago she made a couple of piggy banks that were so amazing I decided I needed to make a bank of my very own. A birdy bank.
I love that papier maché gives you the opportunity to make basically anything out of recycled materials. This is a great project for kids and adults alike- just be ready to take it in shifts over a couple of days so that the form has time to dry between each coat.
Basic Supplies and Tools
- A table cloth or paper cover and an apron. This is a wonderfully messy project!
- A balloon
- Flour and water (to make paste)
- A piece of chipboard (like scrap from a cracker box)
- This template for the feet, beak, wings and tailfeathers (which you will cut from chipboard.)
- Masking Tape
- Glue – Hot glue works great, but other thick glues work in a pinch
- Scissors and craft knife
- Sand paper or sanding block
- Acrylic paint
- ‘ glue or similar
Step One: Starting the Paper Maché and Form
Blow up one balloon about 5.5″ in diameter, and crumple up a piece of paper to make a head about 2.5″ in diameter. Tape the “head” to the balloon*, roughly the opposite side from the tied end. (If you would prefer the inside of the birdy to be smooth, cover the balloon with a layer of paper maché before attaching the head.)
To make your simple paper maché paste, mix one part flour with one part water. (You can change this ratio if you prefer a more watery or thicker paste. Practice makes perfect.) Stir the paste with your finger until it is smooth.
Tear your newspaper into small strips and pieces and begin to coat your body form with a layer of newspaper. Dip each strip into the paste, and pull it through your fingers to remove excess paste and moisture.
Overlap the pieces of newspaper on your form, and cover all but the tied end. It may be helpful to set the balloon on a cup or bowl to lift it off of your surface.
When you have completely covered the form with one layer of newspaper, set it aside to dry. If you have a fan or space heater, set this little guy in front of that and it will dry faster. Make sure to let it dry almost completely before moving to the next layer of material, or you will have a soppy mess. At least wait a few hours.
Step Two: Adding more Detail
Since your bird looks nothing like a bird yet, it’s time to add some appendages. Download and print this template and cut each of the pieces from a piece of chipboard.
To build the birdy legs, cut into one side of the chipboard as shown, and roll the other end into a cylinder. Secure the roll with a couple of pieces of tape.
Then tape across the foot to attach it to the leg. The flap left at the end of the leg will be glued to the base of your balloon form.
Roll the beak to form a cone shape, and tape it in shape. Stuff a little piece of paper into the open end of the cone to make it easier to attach to your birdy head.
Glue works best to secure the wings, legs, beak, and tail feathers to your form. Hold them in place until the glue is holding firmly. When everything is in place, begin to add another layer of papier maché, covering all the new parts of your bird in addition to adding another layer to the main form you’ve already covered.
As you add paper, make sure to leave the end of the balloon visible; this is where you’ll be breaking the balloon and pulling it out. Paper maché is very forgiving and it’s easy to cover up this hole.
When you’ve covered the form with one or two layers of paper, let it dry again. You may find that you have to stop before you’ve completed covering the whole thing because life gets in the way of your messy fun, or your messy fun become a little too messy. No worries! Just make sure that your paper is as smooth as you can make it, and let the bird rest.
Step Three: Removing the Balloon and Making this Guy a Bank
Yes. It looks silly. That’s okay, the best things are silly. When your form is completely dry, you’re ready to remove your balloon. Gently grip the balloon’s knot, and pierce the balloon to let the air out. As it shrinks, it should pull away from your paper. If it sticks in a spot, gently pull it out of the hole.
No bank is complete without a place to put the money. Mark a line down the back of your bird, between the wings, about 1/4″ wide and 1.5″ long. Use a craft knife to carefully trim out the piece you’ve marked.
To finish the bottom of the bank, you have a couple of options. You can either add an access hole for money to be removed or go with the ol’ piñata method– keep the money inside until it’s time to smash! (Which is definitely satisfying.)
If you’d like to make your bank reusable, find a small lid or something else that would work as a plug. Trace around the shape and cut any extra paper. It you’re having trouble keeping the cover in, trace it onto a scrap of chipboard and make a ring the perfect size, then glue that on top of your form and cover it with paper. The chipboard with provide a little extra stability. (Yes, I know this all looks kinda amusing. Giggles are allowed.)
Step Four: The last of the Papier Maché
If your form is feeling pretty secure, it’s time to start adding the last layer of papier maché. The paint will not completely cover the paper (unless you want it to) so this is a great time to start having fun with your paper color and prints. Save gold and orange colored paper for the beak, cover the wings and head in dark colors, and use white newsprint for the breast. When you’re happy with the way it looks, let it all dry overnight!
Step Five: Sanding and Painting
If you’re anything like me, your form will need a little sanding. USe sand paper or a sanding block to smooth off any edges of paper, clumps of paste, or rough edges- making sure not to sand below your papier mache layers.
To make a transparent paint layer, mix equal parts glue and white acrylic paint with a little water. (Add more glue for more transparency, or more paint to cover the paper more opaquely.)
Gently apply a layer of paint and glue to the whole form and let it dry.
When it dries you will still be able to see a lot of your newspaper pattern. If you like, add another layer of white paint, or start to add more colors to bring out details. To keep some of the transparency, you can water down your colored paints and streak them across your form.
Let it all dry, and get ready to fill it with money!
Using this balloon method you can make pretty much any animal you want! I’d love to see!