AIM DIY: Quick Printable Catnip Kicking Bag

September 13, 2016October 28, 2020 | Alison - Adventures-in-Making

From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

In typical cat fashion, my kitties seem to like toys that are not intended to be toys at all. You might think it’s a child-safe plug cover, but they think it’s the neatest thing since canned tuna. For a while they have been sharing a repurposed jack-o-lantern drawstring bag filled with catnip- and I decided it was time to give them something a little nicer. They do love the scale of the jack-o-lantern bag, which is long and wide unlike most catnip toys, so I decided to replicate the scale with a super-simple catnip kicking bag.

I wanted to customize the bags a bit, and I kept thinking about the lovely art Tara Bliven shared with us last month. I asked if she would write up a few feline words for us, and she did! You can use the free printable below to make this cat toy even cattier!

Supplies for two Bags

4 pieces of medium to thick fabric, 10″ x 3.75″
Fabric Scissors and Pinking Shears
Needle and Thread or Sewing Maching
At least 2 teaspoons of dried catnip
OPTIONAL: Inkject Fabric Sheets and Tara’s amazing Fabric Art below

Download and print out the Cat Fabric according to the specifications on the package.

Cut the fabric in half to make a sheet 10″ x 3.75″. Peel the backing paper off the fabric and stack it on top of the two pieces of thick fabric- with “right sides” facing out.

Stitch, 1/2″ in, around three sides and leave the fourth open.

Pour at least a teaspoon of dried catnip in the middle of your pocket…

Close the last side of the bag, and trim around it with pinking shears to limit fraying (and add character.)

Repeat with the second set of materials, and you’re done! A super cute sewing project that’s quick enough that you won’t mind when your kitties shed all over it. Now for the fun part…

(Warning, you are about to be bombarded with too many pictures of my kitties.)

img_6806kickingbag — The dangers of catnip trips. Very unflattering photos.

Success.

A couple of notes

The printable fabric is quite thin and I didn’t trust it to contain the catnip for very long, so I used it as an outside layer only. The catnip itself is contained within two layers of thicker fabric.
If you’re feeling adventurous, try this tutorial to make your own printable fabric!
If you are worried about your print running, try this vinegar bath solution to set your ink.
Tara is a wizard at decorative writing (and many other arts). Visit her website tarabliven.com to find out how you can bring more of her awesomeness into your life.

AIM DIY: Recycled Rainbow Mobile

August 9, 2016October 28, 2020 | Alison - Adventures-in-Making

From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

Rainbows are amazing. They’re awe inspiring in the sky, they are a great way to organize things*, and they are just plain magical.

This little recycled rainbow mobile tries to be a few of those things- and has the added bonus of being a nifty reason to doodle.

SUPPLIES

Thin plastic boxes and containers- like those that salads come in
Scissors
1 1/2″ Diameter Circle Thick Material Punch from Fiskars
Colorful Permanent Markers like Sharpies
A scrap ring, one cut from a plastic container lid
Thin string or baker’s twine
Thread
Safety Pin or Awl
Ruler

Use the thick material punch to cut circles out of every piece of plastic you can find. Don’t worry, the idea of using recycleables for art will make you look insane. Embrace it. (;

Use your rainbow of markers to doodle decorations on each circle. It’s okay if you have an uneven amount of some color because you think orange is terrible, just have fun!

Tie three strings to your top ring, and tie those three together to hang the ring parallel to the ground. Find a place to hang this ring while you work.

Choose one of your most popular colors (purple for me), and poke a small hole near the top of each piece with a safety pin. Cut a piece of thread approximately 12″ long, and string it through one of the holes. Tie the ends of the thread together, and attach it to the hanging ring using a lark’s head knot. Repeat this for each circle of this color.

Choose the next color in the rainbow (blue in my case) and poke each piece like you did before. This time add two inches to your thread for a length of 14″. Attach each of these pieces to your ring.

Continue by adding 2 inches to the length of each new color until you have tied all of your pieces to the ring.

When you have finished, hang it in a bright window and watch it sway and catch the light.

See, sometimes trash-art is fun!

*I may or may not be one of those people who sorts books by color. My librarian mother may be driven insane by this fact.

AIM DIY: Watercolor & Wax Paper Jewelry

August 2, 2016October 28, 2020 | Alison - Adventures-in-Making

From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

Sometimes I come up with a project that I enjoy so much that it’s hard to stop to write a post. This, my friends, is one of those.

It’s a simple combination of watercolor, melting wax, and punching shapes- but it’s oh so satisfying.

SUPPLIES

Thick paper for Watercolor
Watercolor paints and brushes
Pencil
Straight Edge
Paraffin Wax
Scraping Tool, like a vegetable peeler.
Iron, ironing board, towel or other surface to catch wiley bits of wax
Parchment Paper
Scissors
Large Thick Material Punches (optional but recommended) I used circle punches in 2″ diameter, 1.5″ diameter, and 1″ diameter
Small hole punch
Thin cord or ribbon
Jump Rings (optional)

Step One: Paint it

Gather your paper, pencil, straight edge, paints and brushes.

Draw several parallel lines with your pencil to create stripes of varying widths.

Begin filling in each stripe with a color in the order of the rainbow. (ROY G BIV – Red Orange Yellow Green Blue Indigo Violet).

If you fill a small stripe, use a similar color next to it (Orange red and Red for instance.) It’s okay if your paint is a little irregular, or you have small white spaces.

Now it’s time to paint the back of your pendant. Draw some non-parallel lines on a new piece of paper, and fill them in with some of the same colors you used on the other side. Leave a little white space as well. Set your paintings aside to dry.

Step Two: Wax it

Now you will need your ironing setup, parchment paper, and wax. You might have a little wax escape during the ironing process, so it’s a good idea to have a scrap towel or cotton fabric to protect your ironing board. Remember to keep an eye on your ironing so you don’t singe anything!

Sandwich one of your dry watercolor sheets inside a piece of parchment paper. Shred a pile of wax on top. (You can always add more wax, so this is a good time to play!)

Turn your iron to it’s lowest setting, and gently melt the wax between the sheets of parchment paper. You will see the paper start to look wet. Continue working the liquid wax into the paper until it starts to be consistently translucent. You may want to add more wax.

Flip your paper over, and add a pile of wax to the other side. This will be the “glue” that holds your two sides together.

Lay the other piece of paper on top of that pile…

shred some more wax on that, and iron again following the earlier instructions.

Continue to add wax until the papers are translucent and consistently wet looking. When you’re happy with the look, put a little bit of weight on the stack, and let it cool for a couple of minutes.

When it is still warm, but safe to touch, uncover the paper, and use your finger or a tool to smooth any puddles of wax. (Playing in wax is one of my favorite things!) Now let it cool completely (a few minutes.)

Step Three: Punch it

I am loving these thick material punches from Fiskars. I have long abused normal paper punches, and they have a habit of breaking at the worst possible moment. These punches go through everything like butter.

Use a punch (or scissors) to take shapes out of your waxed paper…

until you have a nice little pile of shapes to work with. To turn solid shapes into pendants, punch small holes on one or two sides. You can run cord through these holes (or attach jump rings.)

After you have everything cut out, polish the shapes by using your fingers to rub excess wax off the surface and edges.

Feed thin ribbon, cord, or chain through the holes in your pendants. You can feed your cord through, wrap it several times, or tie a lark’s head knot. Anything goes! Leave enough room to slip the necklace over your head, and you’re set.

Double sided rainbow pendants!

Now I want to wax all the paper. Someone stop me before I go too far!

AIM DIY: Patio Friendly Pile-Up Cushions filled with Styrofoam Peanuts

May 3, 2016October 28, 2020 | Alison - Adventures-in-Making

From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

The weather was nice for a few days in April, uncharacteristically, and began the countdown to the Pacific Northwest Summer. Ahhh; the handful of blissful weeks that makes you fall in love with the trees again, and wipes the memory of the last 8 gray months.

Safety Husband and I have been trying to be more mindful, and that extends to the way we interact with our home. We are who we are [not catalog people] and we want everything at our house to be conducive to the way we live. We have several outdoor areas that would make great external living spaces, but we haven’t done a great job of outfitting them for the task.

All this to explain why I decided I needed to make a giant pile of outdoor cushions that I could lay upon like the Princess and the Pea. I wanted them to be cheap, washable, refurbishable, and also work with our inside decor. Fabric and wood don’t do well outside over the Seattle winter, and I can’t store things in out non-existent storage space. So I put together a handful of pillow forms from scrap material, filled with recycled styrofoam peanuts; then covered them with painted canvas covers. In one afternoon I had 7 assorted cushions, and dreams of the perfect summer.

SUPPLIES

Fabric scissors and optional pinking shears
Sewing machine and thread
Pillow Form Fabric: approximately 24″ (2/3 yard) of 45″-wide lightweight scrap fabric per pillow
Pillow Cover: approximately 24″ (2/3 yard) of 52″ to 60″-wide canvas-type material per pillow
Styrofoam Peanuts: about a grocery sack full per pillow. Make sure that you are using styrofoam peanuts instead of the cornstarch ones that melt under water. Imagine the mess!

DECORATING SUPPLIES

Tulip Color Shot Fabric Color: I used Teal, Blue, and Green.
Scissors
Tape: masking, packing, cello, washi. Whatever you want!
Con-Tact Paper: A great option for cutting out larger masks or covering more material.
Decorative punches and scissors
Compass, or fun shapes to trace

Step 1: Making the Pillow Forms

Take your scrap pillow-form material and fold it so that the selvedged edges touch. Cut the other two sides with pinking shears so that you have an approximately 23″ square (45″x23″ unfolded.) Sew a 1/2″ seam along the two pinked edges, then do the same for about half of the remaining side.

Fill the form about halfway full with peanuts, then sew the opening closed to seal your pillow form.

Hire a professional to test the security of your stitching.

Repeat until you have run out of material. (I made 7 pillows so that I could make a GIANT PILE.)

Step 2: Making the Pillow Covers

There is dirt outside, so you want to make sure that your pillow cover can be easily removed and laundered; this also means you want to pre-wash your fabrics so there is no future shrinkage.

Cut your fabric to about 23″ wide. With the back side showing, fold the width of the fabric into a tube about 22″ wide. The overlapped pieces will make the flap for inserting and removing your pillow form.

Stitch up the two open ends of your tube approximately 1/4″ in.

Then turn the cover inside out using the open flaps. Make sure to press the corner all the way out with your finger or a pencil.

Stitch around the outside edges of your pillow cover, about 3/8″ in- then you’re done!

Step 3: Decorating the Cushions to Match your Life.

Decorating the pillows was definitely the biggest fun in this project (other than sitting in the sun on the cushions later.) If you’re a selfless person, you could share that fun with your family and friends, and let each person design a mask for their own pillow. Masking the pillow is as easy as using tape and scissors. Build shapes out of strips of tape, or cut shapes out of contact paper. (ABOVE: I used a compass to draw circles, then cut and arranged them on the front of my cover.) You could have the initials of everyone in your family, silhouettes of your pets and favorite animals… anything really.

Once you’ve settled on a masked design, take it outside and spray it down with your fabric spray paint. (I used Tulip Color Shot Fabric Color which is washable and flexible.) Remember that spray paint doesn’t ever go on consistently, so embrace the irregularity and leave some patches lighter than others.

After you’ve got a nice coat of paint on, let your cover dry for an hour or so before pulling off the mask.

Then let your covers air out for a few more hours.

When everything is dry (not sticky or smelly) you can put your pillow forms into your covers. Slip the form into the open flap, then push it down under the inner over-lapping flap. Press the corners of the form into the corners of the cover and shake and stomp it until everything looks nice.

Then build the tower of pillow on which you will reign.

Or, you know. Share with your friends.

Wheeee! Pillows.

AIM DIY: Turn a Tea Towel into the Simplest Apron

February 6, 2016October 28, 2020 | Alison - Adventures-in-Making

From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

My cooking style is much like a cartoon: with ingredients flying everywhere, sauces spilling across every surface, and flour covering every inch of my clothing.

Aprons and abundant cleaning cloths are an absolute necessity. Since I like to cook my aprons need frequent washing, so I set out to make one to spare from a fun tea towel. (Before you ask, this lovely tea towel is from Seattle local Sunday Drive Designs.)

SUPPLIES

One pre-washed and lightly ironed tea towel
About 3 yards of fabric ribbon
Corresponding thread
Straight pins
Scissors
A sewing machine or hand needles

This design breaks down very simply into a tie around your waist, and a loop around the back of your neck.

Start by holding the tea towel up in front of you, and marking with a straight pin where your natural waist is. (For me, it was about 1/3 of the way from the top of the tea towel, at about 9″.) Cut a length of about 2 yards from your ribbon, and pin it across your tea towel at the point you marked.

Cut two more lengths of ribbon, on 12″ long and one 24″ long. One each piece, fold about 1″ underneath, and pin to one of the upper corners of the tea towel.

Now to the sewing! I used a straight stitch on my machine to attach the ribbons to the tea towel (which I show below) but if you don’t have a machine, don’t fret! You can hand stitch these pieces on without too-much trouble, just give yourself a little time.

If you’re using a machine, follow the waist tie with a straight stitch, about 1/4″ from the edges.

Then tack the neck straps on each side. (I stitched an “X” shape across the tab for reinforcement.)

With all the ribbon ties attached, slip on the apron and tie the pieces.(The knot of the neck strap will be on one side, since one strip is longer than the other.) Check the length of all the pieces, and trim the ends off of any of the pieces that are way too long. Make sure not to trim any of the pieces too short! You might want to share the apron with someone who is a different size.

Once the pieces are trimmed, take off the apron to finish the edges of the ribbon.

Fold about 3/4″ of the ribbon under, then fold again to hide the raw edge of the ribbon. Pin it flat, and repeat on all of the raw edges.

Finish by stitching the fold down on each end. Bang! Done.

Super simple (and cute) protection from dangerous food-shrapnel.
No more will people know everything about you by the stains on your clothing. You can hide those stains on an apron instead.

Sneaky.

AIM DIY: Target My Heart Pincushion

February 5, 2016October 28, 2020 | Alison - Adventures-in-Making

From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

About 12 years ago I stitched together a utilitarian pillow stuffed with cloth scraps and called it a pincushion. It was my sad companion through many a sewing project, and as much as I wanted to replace it I never made the time.

Well! The time has come.

Seeing as it’s February and Stitches + Threads time, let’s turn Cupid’s target into a nifty little pincushion.

SUPPLIES:

Red and white craft felt
Corresponding thread or embroidery floss
A small scrap of chipboard
A black permanent marker (I used a Sharpie Stained marker.)
Your favorite adhesive
A pair or scissors
Sewing needle
A strong thin magnet
The printed fabric template: to download click on the image below, or here.

* Optional : If you’d like to turn your pincushion into a wrist band you will need a small length of elastic and a second magnet.

First use the “Wrist Guard” template piece to cut a small heart out of chipboard. This will be place inside the pincushion to keep you from pushing pins all the way through. Use your favorite adhesive to attach one magnet to this piece of chipboard.

Next tape a small piece of white felt to the template sheet and use a window to trace the rings of the target shape with your black marker. You may need to go over it a few times to make the rings as dark as possible.

Set this piece aside for a moment to dry or you will end up with marker all over your hands. (Which is fun!) While you are waiting, use the “Heart” template to cut two red heart pieces, then when the target is dry cut just outside of the first dark ring. Keep all your little fabric scraps for the stuffing steps later. (Waste not, want not and all that.)

Place the target piece in the center of one of the heart pieces and pinch or pin them together. Using black thread or embroidery floss whip the target down to attach it to the pincushion. (I used a blanket appliqué stitch around my target, similar to the one Rachel used in her Alphabet Hoop Art DIY . You can watch a video of how it is done here. If this looks tricky to you, use any old stitch you want!)

When the target is all stitched down make a sandwich with the remaining pieces: target+heart piece, chipboard+magnet piece, plain heart piece.

Then use thread (or floss) to stitch the two red felt heart pieces together, beginning at the top of one side. (For this stitching I used a blanket stitch. You can see a video of a pro doing it here. Any stitch should work to make this little pillow, so play around with it!)

When you reach the top of the other side of the heart, stop sewing and collect your scraps to stuff. Any large scraps can be cut into tinier pieces that will fluff up the inside of you cushion.

Start to fill the space between the chipboard wrist guard and the heart+target piece, using a little bit of stuffing at a time. Make sure to press into the point and sides of your heart to make it really puff.

When you’ve got it almost over-full stitch up the remaining open space and tie a firm knot. Tuck your thread-end into the heart or trim it and you’re all done!

So, why did I have you include a magnet? Because magnets are awesome! If you’re prone to losing straight pins like a startled porcupine loses quills you’ll appreciate the pin collecting magic of a strong magnet. Have a magnetic board or fridge in your making space? Smack your pincushion there for safe keeping!

But if you want to really kick your pincushion up a notch…

you can make a magnetic wrist band. Cut a piece of elastic a little bit smaller than your wrist, and glue a magnet to one end. Sew the two ends together to form a loop, stitching around the magnet.

Then you should be able to attach your pincushion temporarily to your wrist whenever it’s convenient.

If you’re anything like me, it will be convenient a lot.

I don’t think I’ll ever look back to the silly old pincushion of yesterday, but I am tempted to make a bunch more of these guys. Maybe a porcupine…

AIM TOOLBOX: Tips for Sharpening a Grumpy Paper Punch

December 18, 2015October 28, 2020 | Alison - Adventures-in-Making

From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

I ask a lot of my tools, which is why I forgive my paper punches when they hesitate to punch happily through yet another piece of cardstock.

Instead, I grab a piece of aluminum foil, fold it several times, flatten and…

punch through it again and again until I have a foil mess…

and a cleaner punch.

Tip shared.

Do you have any tips we should know about? Email your little tricks to [email protected] and we might be able to share them with our little community.

AIM DIY: Photo Album Pop-up Ornaments

December 17, 2015October 28, 2020 | Alison - Adventures-in-Making

From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

Okay. I’ll admit it. I have possibly been making too many ornaments.

The floor is covered in little bits of paper, the ribbons are everywhere, and cat is oh so happy. (Happy and thus in the background of many of my photos.) I can’t help it. I’ve given myself over to the ornament bug, and even though I’ve told myself that these are ‘just this year’s ornaments’, I’m not sure I’ll have the self control to throw them all away.

I need a crafter help line… or maybe I can just spread the decoration disease and have you all join me in the madness. (*evil laughter*)

My sister recently handed over a large bag of family photos, and after the proper period of mortification I decided that I needed to do something with them. The best part about being in charge of photo projects is that you can include only adorable pictures of yourself, and edit out the slightly more awkward times.

I pulled together a selection of photos of family that yelled “HAPPY HOLIDAYS, Y’ALL!” Scanned and shrank them, then pulled out a few basic tools to turn the faces I love into ornaments I’ll cherish.

SUPPLIES

Resized photos printed on medium-heavy weight paper
Extra colored paper or cardstock
Medium to large hole punches– any symmetrical shape will work, I used circles and ovals
Ribbon or string
Buttons, bells, or beads
Paper glue or adhesive

To begin I punched my favorite people out of my favorite photos, and the same number of circles out of cardstock. Then I chose between 4 and 6 of my favorites, the same number of solid circles, and folded each in half– top to bottom.

I chose a button than matched my cardstock, then cut about 16 inches of string and fed it through the button.

I used my Scotch ATG gun to apply adhesive to each folded piece (glue works too).

I attached each piece to the one before it in a stack, alternating photos and cardstock. (Make sure that you don’t accidentally glue your sister in upside-down. She wouldn’t like that. All photos should point the same way.)

I laid the string and button across the spine of my stack (button on the bottom), added a little adhesive to one of the folded pieces, and attached the top and bottom piece to form a ball shape.

Then I fed another button on above the ball, tied a knot, and fluffed open all the pages.

I love how simple they look from far away, but each page is a memory of the holidays and of my family.

I did a few variations, using different punches, and combining shapes on one ribbon; but they are all put together the same way which means I could spend more time remembering good times than obsessing over the process.

It also means it’s a great project for kids, who might get a thrill out of punching holes out of photos.

and keeping them forever.

AIM DIY: Playing Card Ornaments

December 10, 2015November 7, 2020 | Alison - Adventures-in-Making

From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

An old deck of cards in one hand, and the perfect Christmas Tree outside… something weird’s gonna happen.

We love games at this house. Card games, board games… you name it. I love to buy my children card games for Christmas or on their birthday as we love being able to play games with each other as a family. There are so many different card games out there that 8 year olds love to play with and so I try and find ones that are suitable for their age. We enjoy playing with them that much that I’m replacing them more regularly than I’d like to be. I don’t love worn-out cards, though, so I’ve been looking for a clever way of getting rid of a couple of our older decks. After playing with strips of paper as Christmas ornaments, I started thinking about ways to turn flat cards into 3-d shapes. Internet searches gave me a few options, including this great tutorial for making ornaments out of MTG playing cards. After following the tutorial, I made a couple of tweaks and ended up with another great collection of ornaments for our outdoor holiday tree.

Supplies

A deck of cards
Thin-ish wire: I used 22 Gauge floral wire
Assorted beads or buttons: Make sure the wire will fit through the holes.
Wire clippers and pliers
Craft knife or paper cutter
Awl or large needle for piercing cards
Ribbon or string

To begin you will cut several playing cards into 1/2″ strips. Choose 16 of those pieces to turn into your first ornament.

Poke a hole, at the bottom and top of each piece, approximately 1/4″ from the end. (You should be able to pierce through multiple cards at once.)

Trim a length of wire, approximately 10″ long, and put a small loop in one end. String at least one bead as a stopper, then start feeding your card pieces on, one at a time. This will be the bottom of your ornament, and the side showing from the bottom (shown above) will be the side of the card facing out on your ornament.

IMG_3527_playingcardornaments — The red side will be hidden on the inside of this ornament.

Once you have all your card pieces fed on the wire, add about 1-1/2″ of beads as spacers.

Starting with the bottom piece of card, gently feed the wire through the pierced hole at the other end.

Do the same with the next lowest piece of card, letting it rest against one side. Repeat with the next lowest piece of card EXCEPT let it rest on the other side of the center.

Repeat this action on each piece, going back and forth between each side of the ornament. It should begin to form a sphere.

There should be just enough space to feed the last (most interior) piece through. If you feel like the pieces are too cramped, you may want to gently tear a piece or two off your wire.

When you have all the pieces wrapped back around, add another bead or two, make a loop in the wire, and trim. Feed a ribbon through the loop, and you have a nifty ornament!

Other things to try

Make the spacer inside the ornament longer for a more spherical ornament, or make it shorter for a more compressed “space saucer” ornament. The different shapes will need a slightly different number of card pieces, but I’ve found that they all use between 14 and 16 pieces.
String two ornaments on the same wire for a more complex shape.
Mix and match back pieces and front pieces for a striped pattern.
String an extra piece of beaded wire or string to the bottom of the ornament for even more decoration.
Go crazy with bead spacers and see what happens.

What do you think? Trash to treasure?

AIM DIY: Simple Trees for Your Chipboard Forest

December 2, 2015October 28, 2020 | Alison - Adventures-in-Making

From 2014-2016 I chronicled my crafty endeavors on the site Adventures-in-Making. I’ve selected a few of those DIY’s, Recipes, and other posts to share on the site.

Even before I was done building little chipboard houses I knew they would need a little setting to live in. I wanted to come up with a simple and flexible tree template that I could make a whole forest out of. Inspired by my old paper bird project, I used strips of chipboard to build these trees.

Supplies

Scrap chipboard: from the backs of notepads or boxes. My pieces were 8.5×11″
You favorite paper glue
Clothespins or clips
Craft knife
Scoring Tool: a bone folder or dull knife work great

I began by making two score lines along the long side of the board, at .5″ and at 2.5″.

Then I cut two pieces, 1″ wide, off the other side for the trunk of my tree. The remaining piece of chipboard had my score marks on it, and I trimmed it into 1″ pieces (each piece has the same score marks).

I applied glue to the trunk pieces, and clipped them together to dry.

While the trunk glue was drying, I folded each of my small pieces along the score marks, forming an L.

Piece by piece, I applied glue to the .5″ flap and the top of the L…

then clipped them to the trunk. In this picture you can see that I folded the two pieces of the trunk away from each other at the base; this will allow the trees to sit by themselves.

I continued to add tree pieces until I liked what I saw (typically between 2 and 4 tiers), holding each piece with a couple of clips.

When I was happy, let the glue sit overnight, held by the clips. (Happy little trees, as the man said.)

On some I trimmed the top a bit, some I left tall. I love the way the variety turned out. These would be great with snowy glitter added, or paint. I’m just happy to have a forest for my little chipboard houses.

Trees for the little paper world.

Yes, I know I sound crazy. Now go make something!

(;

So, There.

So There Letterpress and Stationery Studio in Issaquah

craft

AIM DIY: Quick Printable Catnip Kicking Bag

Supplies for two Bags

A couple of notes

AIM DIY: Recycled Rainbow Mobile

AIM DIY: Watercolor & Wax Paper Jewelry

SUPPLIES

Step One: Paint it

Step Two: Wax it

Step Three: Punch it

AIM DIY: Patio Friendly Pile-Up Cushions filled with Styrofoam Peanuts

SUPPLIES

DECORATING SUPPLIES

Step 1: Making the Pillow Forms

Step 2: Making the Pillow Covers

Step 3: Decorating the Cushions to Match your Life.

AIM DIY: Turn a Tea Towel into the Simplest Apron

SUPPLIES

AIM DIY: Target My Heart Pincushion

SUPPLIES:

AIM TOOLBOX: Tips for Sharpening a Grumpy Paper Punch

AIM DIY: Photo Album Pop-up Ornaments

SUPPLIES

AIM DIY: Playing Card Ornaments

Supplies

Other things to try

AIM DIY: Simple Trees for Your Chipboard Forest

Supplies